Licensed & Insured · MD License 7788 · Family-Owned Since 2005

Backup Power & EV Charging › Generator Installation

Generator installation in Harford County, MD

When the power goes out, the sump pump, the well and the furnace go with it. We install standby generators and portable generator hookups that keep the circuits you care about running, sized to your house and connected so the generator can never feed the utility lines.

STANDBY · PORTABLE

NEC ARTICLE 702

BGE · DELMARVA

Get a free estimate

We reply within 24 hours. Emergencies: 410-808-4215
Form B — Quick Estimate

MD License 7788

Licensed & insured

Family-owned

Since 2005

Veteran-owned

Start here

Picking the generator setup that fits your house

Most generator calls come the week after an outage. The sump pump stopped during a spring storm and the basement took on water. The well pump went quiet and nobody could flush. The freezer warmed up over a two-day outage after a July thunderstorm. Generator installation is how you keep those things running next time, and there are two main ways to do it: a permanent standby generator that starts by itself, or a portable generator that you roll out and plug into an inlet on the outside wall.

We help you choose by looking at what you need powered, what your panel can carry, and where a generator can safely sit on your lot. This page covers generator installation of both kinds. For the wider picture of backup power, surge protection and EV charging, start with our backup power and EV charging page, or read about our generator work in Bel Air.

What you may be noticing

A photo or video helps us narrow it down. An on-site check confirms the cause.

How it works

From a storm outage to a house that keeps running

YOU NOTICE

A thunderstorm takes the power out for a day or more

Trees on lines cause many outages here, and rural roads at the end of a long feeder are often restored last.

WHAT'S HAPPENING

Every circuit in the house stops at once

The panel has no other source. Pumps, the furnace blower, the fridge and the lights all wait for the utility.

WHY IT MATTERS

Food spoils, the basement floods, and cords snake through windows

A generator plugged into an outlet or a dryer receptacle can also backfeed the street and hurt someone working on the line.

WHAT WE DO

We size the generator and connect it through a transfer device

A standby unit with an automatic transfer switch, or a portable unit with an inlet and interlock, priced before work starts.

What's going on

How a generator connects to a house

During an outage your house is cut off from the utility, but the wires between your meter and the street are still connected. A generator gives the house a second source of power, and that source has to be connected so the two can never meet. If generator power flows back out through the meter, the transformer on the pole steps it up to thousands of volts on the line. That is backfeed, and it is the reason utility crews treat every downed line as live.

The part that prevents it is a transfer device. A transfer switch moves selected circuits, or the whole house, from utility power to generator power. An interlock is a listed plate on the panel that makes it impossible to switch on the generator breaker while the main breaker is on. Either way, only one source feeds the house at a time. The National Electrical Code covers these optional standby systems in Article 702.

A standby generator is wired in permanently and runs on natural gas or propane. Its automatic transfer switch watches the utility power. When the power drops, the generator starts, comes up to speed, and the switch moves the load over. When the utility returns, it switches back and the generator cools down and shuts off. A portable generator does the same job by hand: you roll it out, start it, plug a cord into the inlet box, and switch over at the panel.

Sizing matters for both. Motors in well pumps, sump pumps and air conditioners draw a burst of current when they start, often several times what they use while running. A generator sized only for running watts can stall or trip its breaker the moment a pump kicks on, so we count starting loads, not just the total.

What a generator changes for your home

Done right, the sump pump keeps up through a spring storm, the well keeps water in the taps, the fridge and freezer stay cold, and the furnace blower keeps the heat on during an ice storm. With a standby unit that happens whether anyone is home or not, which matters if you travel or own a second property.

Done wrong, the costs are real. An undersized generator trips each time the well pump starts. A cord through a window keeps the house open to the weather and pulls the generator close to the walls. A homemade double-ended cord into a dryer outlet can backfeed the street and can damage the generator when the utility comes back. Carbon monoxide is the other risk: a portable generator must run outdoors, well away from windows, doors and vents, and never in a garage, even with the door open. Every home that runs one should have working carbon monoxide alarms.
Fallen tree limb on power lines after a thunderstorm in Harford County, Maryland

STORM OUTAGES

Summer storms and ice bring lines down across all three counties
Electrician wiring an automatic transfer switch beside a home breaker panel in Maryland

TRANSFER SWITCH

One source feeds the house at a time

What we do

Standby generators and portable hookups, installed to code

Every generator job starts with a list. We walk through what you want running during an outage, then check your panel, your service size and the loads on each circuit. That list decides the approach. If you want the whole house to carry on as normal, central air included, a standby generator with an automatic transfer switch is the usual answer. If you want the essentials, such as the sump pump, well pump, fridge, furnace and some lights, a portable generator with an inlet and interlock often covers it for much less.

For portable setups we mount a weatherproof inlet box on an outside wall, run the cable to the panel, and add a listed interlock kit or a manual transfer switch. You get a cord matched to the inlet and to your generator. We cover that work in detail on our inlet, interlock and transfer switch page, and on our page for Generac® portable generator hookups.

For standby generators we wire the automatic transfer switch, the feeder to the generator and its control wiring, and we confirm the panel and service can take the switch you choose. Some switches cover the whole house at the service; others cover a group of essential circuits. The unit sits on a pad placed where the manufacturer’s clearances and the county allow, away from windows, doors and vents. The gas or propane connection is fuel work done by a licensed gas fitter or your propane supplier, and we plan our part around theirs.

We pull the electrical permit when the job requires one and meet the inspector. A video of your panel with the door open, your meter, and the spot you have in mind for the generator is enough for a starting estimate. It cannot show how loaded the panel really is or what the route to the outside wall looks like, so the final scope is set on site.

How the visit goes

How a generator installation goes

A portable hookup is often a one-day job. A standby install takes longer because the pad, the fuel line and the inspection all have to line up. You get the schedule before we start.
Michael Cliffe standing behind the Snapper Electric truck with ladders on the roof rack

SINCE 2005

Owner-led jobs across three counties

1

Load list and site check

We go through what you want powered, check the panel and service, and look at where the generator or inlet can safely go.

2

Options and price

You get our recommendation, standby or portable, the size and why, with up-front pricing before any work starts.

3

Permit and scheduling

We pull the electrical permit when required and line up our work with the fuel supplier on a standby unit.

4

Installation

We mount the inlet or transfer switch, run and connect the wiring, and set up the interlock or the automatic switching.

5

Test, inspection and walkthrough

We run a full switch-over test, meet the inspector, and show you how to operate the system.

Free video estimate

Need a Quick Quote?

Send a short video to 410-808-4215 showing the area where you’re experiencing an issue or where you’d like work completed. Please include as much detail as possible so we can provide the most accurate estimate.
Please Note: Quotes provided from videos are estimates based on the information shown. If additional issues, repairs, materials, or site conditions are discovered that were not visible in the video, the final cost may vary. A more detailed video helps ensure the most accurate quote.

Cost factors

What changes the price of a generator installation

We don’t give a flat number before we see the house. These are the things that move it up or down.

Standby or portable

A standby generator with an automatic transfer switch is a bigger project than an inlet and interlock for a portable.

How much of the house

Backing up the whole house takes a larger generator, larger wire and a larger transfer switch than a few essentials.

Distance and route

How far the generator or inlet sits from the panel, and what the cable has to pass through on the way.

Panel condition and space

A full or worn panel may need breaker work, a subpanel or replacement before backup power can connect.

Pad and fuel

On a standby unit, the pad and the gas or propane work by the fuel supplier are part of the total.

Permits and inspection

County permit fees and the inspection visit, which we schedule for you.
A video estimate gets you a starting figure; the on-site assessment confirms it. Ask about our veteran, teacher and senior discounts.

Local notes

Generator permits, placement and utilities by county

Generator wiring needs an electrical permit in all three counties. We handle the permit and inspection when the job requires one.

Harford County

Electrical permits go through the Permit Center at 220 S. Main St in Bel Air, under the 2023 NEC with county amendments. Northern Harford, from Darlington to Jarrettsville and Whiteford, sits on long rural lines, and many homes there run well pumps that stop with the power. Most of the county is BGE, with Delmarva Power near the Pennsylvania line.

Baltimore County

Permits, Approvals and Inspections in Towson issues the permit, and the work must be done by a county-registered licensed contractor under the 2023 NEC. On the waterfront in Essex, Middle River and Bowleys Quarters, where Isabel flooded homes in 2003, we keep generators and inlets above likely high water. The utility is BGE.

Cecil County

The Permits and Inspections Division in Elkton handles electrical permits, with the 2023 NEC in force for permits from August 2, 2025, and inspections by third-party agencies. North East, Rising Sun and the farm country around Fair Hill are on Delmarva Power.

Related services

Work that often goes with a generator

Inlet, interlock and cord hookups for Generac portables.
The safe link between a portable generator and your panel.
Protects electronics when the power drops and comes back.
Dedicated sump circuits and backup options for wet basements.
Pump circuits, pressure switches and control boxes on rural lots.
When the panel needs room or capacity before backup power connects.
Alarms on every level, especially in homes that run a generator.
Level 2 charging planned around the same panel capacity.

Service areas

Where we install generators

Generator installation across Harford County, eastern Baltimore County and western Cecil County. Pick your town for local details.

Reviews

What neighbors say

Posted on Google Google
Kyle Harbaugh profile picture
Kyle Harbaugh
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I called Snapper Electric for an after-hours service late on a Sunday evening. Unfortunately, they weren't able to make it to my house but diagnosed the problem over the phone and got me on the right track calling BGE. This is what great customer service is all about! In the past, I've used them from everything from light installs to outlet rebuilds. All the work has always been done to perfection.
Posted on Google Google
Alice Alice profile picture
Alice Alice
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Replaced our outdated electrical panel and fixed a few wiring issues the same day. Professional, punctual, and everything works perfectly now.
Posted on Google Google
monte combs profile picture
monte combs
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
And his service remains 5 star. This was the first time that I have used Mike but rest assure it will not be the last. He was quick, he was honest and his work was exemplary and his prices are more than reasonable. Keep up the good work SNAPPER!
Posted on Google Google
Linda Diaz profile picture
Linda Diaz
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Maryland.... NEED AN ELECTRICIAN?..... Look no further! Words escape me at the amazing customer service delivered by Mike Cliffe(Master Elec.) at Snapper Electric. I called to inquire about services to uninstall my Chargepoint EV home charger. Michael said he can come by to work on this for me. He asked me to send him pics so he can advise properly. I sent the pics and Michael responds back with where to look and how to uninstall. I was shocked! No call charge. No service charge. Just the instructions and he wishes me an amazing weekend!!! Honest and great customer service 👍
Posted on Google Google
Mark C profile picture
Mark C
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Mike came out, quickly diagnosed the problem and fixed it very quickly. He is great, and very reasonably priced! Would definitely use them again!
Posted on Google Google
M G profile picture
M G
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Great work done after a thoughtful discussion on all options
Posted on Google Google
Steve Somers profile picture
Steve Somers
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I bought a new electric range and didn't realize the old one was hard wired in. I called Mike and he was out right away to get a new outlet installed for the new range. I highly recommend!! Super Fast and Professional!!!
Posted on Google Google
John Brodrick profile picture
John Brodrick
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I have had them do a few jobs for me including installing a generator outlet for the house and some wiring throughout the house. He took the time to explain options and what was best to fit my needs. Overall very professional, on time and did great work. Highly recommended.
Posted on Google Google
Ricky Godbolt profile picture
Ricky Godbolt
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I highly recommend Snapper Electric.
They provided guidance in selecting and installed a back-up generator as well as put lights in several closets. The electrician was pleasant, cleaned up after projects and provided in-depth hands on instruction on use of generator. He also provided easy-to-follow instruction on electric panel to guide us as we used the generator. Definitely will use his services in future.
Thomas Heimiller
Kingsville, MD
Snapper installed an Interlock system for my generator and supplied me with a 40-foot extension cord so I can run the generator from the shed. Gave me an estimate for exactly what I wanted done and didn't try and up sell me to something more expensive. Like other estimates I had gotten. Very Nice and very informative about the whole job.
Ricky Wishon
Bel Air, MD
Mike was able to come out and assist us very quickly. He was polite and explained exactly what needed to be done to fix our problem. Very professional work done in a timely manner. Definitely recommend!
Shannon Baumgart
Google review

From the blog

Read more about this

Which kind of backup power fits your home and budget.
Adding up the well pump, sump, fridge and furnace.
Why a dryer-outlet hookup endangers line crews and your family.

FAQ

Generator installation questions

It depends on what you want powered and how much you want to do during an outage. A standby unit starts on its own and can run the whole house, central air included. A portable with an inlet and interlock covers the essentials for less, but someone has to roll it out, start it and refuel it. We lay out both for your house.
We work it out from your list of must-run loads, counting the starting surge of motors like the well pump, sump pump and air conditioner. A house on public water with a gas furnace needs far less than a rural home with a well, a sump and electric heat.
A standby generator sized for it can. Most portables cannot start a central air compressor along with everything else, and some cannot start one at all. If air conditioning matters to you, tell us up front, because it often decides standby versus portable.
Yes. Connecting a generator to house wiring without one can send power back onto the utility lines and endanger line crews. It can also damage the generator when utility power returns. An interlock or transfer switch makes sure only one source feeds the house.
A standby unit goes where the manufacturer’s clearances and the county allow, away from windows, doors and vents. A portable should run in the open, well away from the house; safety agencies such as the U.S. Consumer Product Safety Commission advise at least 20 feet, with the exhaust pointed away. We place the inlet so the cord reaches that spot.
The fuel connection is gas work, done by a licensed gas fitter or your propane supplier. We handle the electrical side, tell you what the fuel side needs, and schedule our work around theirs.
Generator wiring needs an electrical permit in Harford, Baltimore and Cecil counties. We pull it when the job requires one and meet the inspector. A standby unit’s pad and fuel line may involve their own approvals, which we flag during the estimate.
With a transfer switch or interlock the house never connects the two sources, so the utility has nothing to switch. What utilities warn against is connecting a generator without one. If you are unsure about your account or a meter question, we’ll tell you who to call.
Yes. Text a video of the panel with the door open, the panel label, the meter and where you’d like the generator or inlet to 410-808-4215. You get a starting estimate; the final price is set on site.
Michael Cliffe, owner of Snapper Electric

Reviewed by Michael Cliffe, Owner · Maryland State Licensed Contractor, License 7788

Written by the Snapper Electric team · Last updated October 25, 2026

Electrical work can be dangerous. The information on this page is general guidance for homeowners in Maryland and is not a substitute for an on-site assessment by a licensed electrician. Always turn off power at the breaker before touching any wiring, and call 911 if you smell burning, see sparks, or have an active electrical fire.

Ready when you are.

Call, text, or send the form. We’ll tell you what we see, what it means for your home, and what it costs before any work starts.
Office hours Mon–Sat 8 AM–5 PM · 24/7 for electrical emergencies
Snapper Electric turtle mascot