Licensed & Insured · MD License 7788 · Family-Owned Since 2005

Rewiring & Home Wiring › Perry Hall, MD

Rewiring in Perry Hall, MD

In a Honeygo-era house, rewiring usually means new circuits for a basement or kitchen remodel. In older Perry Hall, it can mean replacing ungrounded or aluminum circuits. We look at what your house actually has, then rewire the rooms that need it and leave sound wiring alone.

ZIP 21128

PARTIAL + REMODEL

MD LIC #7788

Get a free estimate

We reply within 24 hours. Emergencies: 410-808-4215
Form B — Quick Estimate

MD License 7788

Licensed & insured

Family-owned

Since 2005

Veteran-owned

Start here

Two kinds of Perry Hall house, two kinds of rewire

Perry Hall splits neatly by age. The Honeygo growth area filled in from the 1990s through the 2010s with colonials and townhomes on modern grounded wiring. Older Perry Hall, closer to Belair Road, has homes built decades earlier. Our rewiring and home wiring page covers rewiring in general, and our Perry Hall electrician page covers the EV chargers, hot tubs and panel work we do in town. This page is about rewiring in both halves of Perry Hall.

In the newer homes, a whole-house rewire is almost never the answer. The calls are about a basement being finished, a kitchen wall coming down, or a run of outlets that stopped working. In the older homes, the questions are the familiar ones: two-prong outlets, cable that’s showing its age, and in some late-1960s and 1970s houses, aluminum branch circuits. We start by telling you which situation you’re in, and we don’t sell a bigger job than the house needs. If a few reworked connections or two new circuits solve the problem, that’s what goes on the quote.

Rewiring in Perry Hall

Not sure we cover your street? Call or text 410-808-4215.

Why it comes up here

Why Perry Hall homes need rewiring, new and old

Start with the Honeygo houses. They were wired with grounded copper cable and usually have 200-amp service, so the wiring itself is rarely worn out. What changes is the house. Owners finish the basement, turn a dining room into an office, open the kitchen to the family room or add a sunroom. Each of those projects moves walls, adds rooms and asks for circuits the builder never planned. Remodel wiring done properly is a partial rewire: new home runs to the panel, not one more outlet tacked onto the nearest circuit.

Builder-grade devices are the other recurring issue. Many homes of that era have outlets wired through push-in terminals on the back of the device. Over twenty or thirty years those connections can loosen, and because outlets in a room are chained together, one bad joint can take out every outlet downstream while the breaker stays on. The fix is usually to rework the connections along the run, not to rewire the house.

Older Perry Hall is a different story. Homes there may still have ungrounded two-wire cable, original circuits shared across several rooms, and splices added by past owners in the basement ceiling. Some houses from the late 1960s and 1970s were wired with solid aluminum branch circuits, which can loosen and overheat at the connections. Those need either copper pigtails at every connection point or replacement with copper. Many older homes here are also on 100-amp service, and the owners want the same things Honeygo families have: a hot tub, a charger in the driveway, central air that doesn’t dim the lights. New loads like those are a good moment to replace tired circuits at the same time.

Both halves of town share one thing: unpermitted basement work. A previous owner’s DIY finished basement with no AFCI protection and junction boxes buried behind drywall is something we find often enough to look for every time. It tends to surface when a breaker starts tripping, when a new owner wants to change the layout, or when a buyer’s inspector asks for the permit history.
Basement framing with new electrical boxes and cable during finishing

BASEMENT ROUGH-IN

New circuits before the drywall goes up
Electrician's hands crimping a copper pigtail onto aluminum wiring inside an outlet box.

COPPER PIGTAIL

A listed repair on an aluminum circuit

What we do

How we handle rewiring in Perry Hall

Every job starts with a look at the panel and the circuits. In a Honeygo home, that means checking spare capacity and open breaker spaces before a remodel, tracing any dead run of outlets to the connection that failed, and opening up any previous-owner basement wiring to see what’s behind it. In an older home, we test each room for ground, identify the cable type, check for aluminum and map the circuits.

For remodels, we work with you or your contractor from the framing stage. A finished basement gets its own bedroom and living-area circuits on AFCI breakers, GFCI protection where the code requires it, a dedicated circuit for the sump pump, and lighting planned before the ceiling goes up. A kitchen gets its small-appliance circuits, dedicated lines for the dishwasher, disposal and microwave, and island outlets placed to code. All of it is roughed in and inspected before drywall. If the basement is getting a bathroom or a wet bar, those get their own GFCI-protected circuits and an exhaust fan on the bathroom circuit.

In older Perry Hall houses, we replace the worst circuits first, usually the kitchen, bathrooms and bedrooms, with grounded copper and tamper-resistant outlets. On aluminum circuits we either pigtail every connection with connectors listed for aluminum-to-copper or replace the run, whichever fits the rest of the job. If the panel is an older model on 100-amp service and can’t take the new circuits, a panel upgrade goes into the same plan.

Planning ahead pays off in Perry Hall more than most places, because so many projects here stack up. If a hot tub or an EV charger is on the list for next year, we size the panel and leave space for it now, so the basement or kitchen circuits don’t use up the last open breaker spaces. Either way, you get a written list of what’s sound, what needs replacing, and what each part costs before any work starts.

How the visit goes

How a Perry Hall rewiring job runs

Remodel jobs follow your contractor’s schedule. Older-home rewires follow your family’s, room by room, so you’re never without a kitchen and a bathroom on the same day.
Michael Cliffe standing behind the Snapper Electric truck with ladders on the roof rack

SINCE 2005

Owner-led jobs across three counties

1

Look at the house and the plan

We check the panel, test the circuits and, for a remodel, walk the space with your plans or your contractor to see where every wall and fixture is going.

2

Written scope and price

You get an up-front price for each part of the work, with options where they exist, such as pigtailing versus replacing aluminum circuits.

3

Permit and rough-in

We pull the Baltimore County permit, run the new circuits while walls are open or fish them in occupied rooms, and pass the rough-in inspection before drywall or patching.

4

Finish and test

Outlets, switches and fixtures go on, every circuit is load-tested, the final inspection is passed, and the panel directory is rewritten. You’ll know which circuit feeds which room when we leave.

Free video estimate

Need a Quick Quote?

Send a short video to 410-808-4215 showing the area where you’re experiencing an issue or where you’d like work completed. Please include as much detail as possible so we can provide the most accurate estimate.
Please Note: Quotes provided from videos are estimates based on the information shown. If additional issues, repairs, materials, or site conditions are discovered that were not visible in the video, the final cost may vary. A more detailed video helps ensure the most accurate quote.

Cost factors

What changes the price of rewiring in Perry Hall

A remodel rough-in and an older-home rewire are priced differently. These factors apply to both.

Open walls or closed

Wiring a framed basement or gutted kitchen is faster than fishing cable through finished rooms.

Number of circuits

Each new home run to the panel, plus the outlets, switches and lights it feeds.

Wire type in older homes

Pigtailing aluminum, adding grounds or full replacement each carry a different scope.

Panel spaces and capacity

A full panel may need a subpanel or a replacement before it can hold new circuits.

Past DIY work

Unpermitted basement wiring has to be opened, checked and corrected before new work ties in.

Permit and inspections

Baltimore County permit fees, plus rough-in and final inspections.
A video estimate gets you a starting figure; the on-site assessment confirms it. Veteran, teacher and senior discounts are available.

Permits

Permits in Baltimore County

Baltimore County requires a permit for nearly all electrical work, including remodel wiring and rewiring, and the permit must be pulled by a county-registered licensed electrical contractor through Permits, Approvals and Inspections at 111 W. Chesapeake Ave in Towson. Permits issued after August 31, 2023 are inspected to the 2023 NEC. We pull the permit when the job requires one and meet the inspector at rough-in and final.

If you’re finishing a basement, ask your general contractor whether the electrical permit is separate from the building permit. In most cases it is, and the electrical rough-in has to pass before insulation and drywall. Keep the records; a buyer’s inspector will ask about the basement someday. If the project includes a service upgrade, BGE handles the meter disconnect and reconnect, and we schedule it so the house is without power for as little of the day as possible.

Baltimore County permit file

PERMIT OFFICE

Baltimore County Permits, Approvals & Inspections, 111 W. Chesapeake Ave, Towson · 410-887-3900

CODE IN FORCE

2023 NEC for permits issued after Aug 31, 2023

UTILITY

BGE

01

Permit

We apply for the permit before work starts, when the job requires one.

02

Work to code

We wire it to the code your county enforces, with the right parts for the job.

03

Inspection

The county inspector checks the work before walls close or the power is restored.

04

Walkthrough

We show you what we did, what passed and anything worth planning for next.

Reviews

What neighbors say

Posted on Google Google
Kyle Harbaugh profile picture
Kyle Harbaugh
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I called Snapper Electric for an after-hours service late on a Sunday evening. Unfortunately, they weren't able to make it to my house but diagnosed the problem over the phone and got me on the right track calling BGE. This is what great customer service is all about! In the past, I've used them from everything from light installs to outlet rebuilds. All the work has always been done to perfection.
Posted on Google Google
Alice Alice profile picture
Alice Alice
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Replaced our outdated electrical panel and fixed a few wiring issues the same day. Professional, punctual, and everything works perfectly now.
Posted on Google Google
monte combs profile picture
monte combs
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
And his service remains 5 star. This was the first time that I have used Mike but rest assure it will not be the last. He was quick, he was honest and his work was exemplary and his prices are more than reasonable. Keep up the good work SNAPPER!
Posted on Google Google
Linda Diaz profile picture
Linda Diaz
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Maryland.... NEED AN ELECTRICIAN?..... Look no further! Words escape me at the amazing customer service delivered by Mike Cliffe(Master Elec.) at Snapper Electric. I called to inquire about services to uninstall my Chargepoint EV home charger. Michael said he can come by to work on this for me. He asked me to send him pics so he can advise properly. I sent the pics and Michael responds back with where to look and how to uninstall. I was shocked! No call charge. No service charge. Just the instructions and he wishes me an amazing weekend!!! Honest and great customer service 👍
Posted on Google Google
Mark C profile picture
Mark C
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Mike came out, quickly diagnosed the problem and fixed it very quickly. He is great, and very reasonably priced! Would definitely use them again!
Posted on Google Google
M G profile picture
M G
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Great work done after a thoughtful discussion on all options
Posted on Google Google
Steve Somers profile picture
Steve Somers
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I bought a new electric range and didn't realize the old one was hard wired in. I called Mike and he was out right away to get a new outlet installed for the new range. I highly recommend!! Super Fast and Professional!!!
Posted on Google Google
John Brodrick profile picture
John Brodrick
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I have had them do a few jobs for me including installing a generator outlet for the house and some wiring throughout the house. He took the time to explain options and what was best to fit my needs. Overall very professional, on time and did great work. Highly recommended.
Posted on Google Google
Ricky Godbolt profile picture
Ricky Godbolt
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I highly recommend Snapper Electric.
He provided all of the electrical work for our basement. He was outstanding.
Michael Kleinfelder
Havre de Grace, MD
They provided guidance in selecting and installed a back-up generator as well as put lights in several closets. The electrician was pleasant, cleaned up after projects and provided in-depth hands on instruction on use of generator.
Thomas Heimiller
Kingsville, MD
Service and support was excellent. Mike was available early and came same-day to support a surprise appliance install issue we had. He did excellent work, adapted to the needs of the situation and laid out the options clearly.
Ken Judy
Homeowner

From the blog

Read more about this

AFCI, lighting, sump circuits and permits for a basement project.
Is it safe, and what a pigtail repair involves.

FAQ

Rewiring questions from Perry Hall homeowners

A whole-house rewire, very rarely. The cable in homes of that age is grounded copper and should last a long time. What does come up is new wiring for remodels, repairs to outlets with failed push-in connections, and correcting a past owner’s basement wiring. Those are partial jobs, and we price them that way.
Usually it’s a failed connection, not failed cable. Outlets are chained together, and when one push-in terminal or splice loosens, everything past it goes dead. Check for a tripped GFCI first, often in a bathroom, garage or the basement. If that’s not it, we trace the run, find the bad connection and rework the joints so it doesn’t happen again.
Yes. We prefer to walk the space at the framing stage, mark outlet, switch and light locations with you, and confirm the panel has room for the new circuits. Then we rough in, pass the electrical inspection before insulation and drywall, and come back to trim out when the walls are finished.
Look for “AL” or “ALUMINUM” printed on exposed cable in the basement, without touching it, and don’t open outlets yourself. Then have the connections checked. Most aluminum-wired homes can be made safe with copper pigtails at every outlet, switch, fixture and splice; replacement with copper makes sense if walls are being opened anyway.
Sometimes. We open a sample of boxes, check the circuits against the panel and look for AFCI protection, proper boxes and correct wire sizes. Some DIY basements need only a few corrections; others need the circuits redone. We tell you which, item by item, with a price.
Yes, for a starting figure. Text a video of the panel with the door open, the space you’re remodeling or the outlets that stopped working, and any exposed basement cable to 410-808-4215. The final price follows the on-site visit, since walls hide most of the wiring.
Michael Cliffe, owner of Snapper Electric

Reviewed by Michael Cliffe, Owner · Maryland State Licensed Contractor, License 7788

Written by the Snapper Electric team · Last updated October 25, 2026

Electrical work can be dangerous. The information on this page is general guidance for homeowners in Maryland and is not a substitute for an on-site assessment by a licensed electrician. Always turn off power at the breaker before touching any wiring, and call 911 if you smell burning, see sparks, or have an active electrical fire.

Ready when you are.

Call, text, or send the form. We’ll tell you what we see, what it means for your home, and what it costs before any work starts.
Office hours Mon–Sat 8 AM–5 PM · 24/7 for electrical emergencies
Snapper Electric turtle mascot