Licensed & Insured · MD License 7788 · Family-Owned Since 2005

Rewiring & Home Wiring › Timonium, MD

House rewiring in Timonium, MD

A 1950s rancher with two-prong outlets, a 1970s split-level with silver-colored wire at the switches, or a kitchen remodel that needs more circuits than the house ever had? We sort out which wiring you have in your Timonium home and replace what needs replacing, one floor or one room at a time.

ZIP 21093

RANCHERS + SPLITS

MD LIC #7788

Get a free estimate

We reply within 24 hours. Emergencies: 410-808-4215
Form B — Quick Estimate

MD License 7788

Licensed & insured

Family-owned

Since 2005

Veteran-owned

Start here

Mid-century Timonium houses, and which wiring era yours is from

Walk the streets off York Road and you’ll see what Timonium is mostly made of: brick ranchers, split-levels and some two-story colonials put up between the 1950s and the 1970s. That twenty-year span covers three different kinds of branch wiring, and which one you have decides what a rewire involves. Our rewiring and home wiring page explains the work in general, and our Timonium electrician page covers panels, lighting and the rest of what we do in town.

The early houses often have two-wire cable with no ground. The middle years brought grounded cable, though sometimes with too few circuits for a modern kitchen. And some homes built from the mid-1960s to the mid-1970s were wired with solid aluminum. We identify which you have at the first visit, because a ranch-house rewire, a ground retrofit and an aluminum repair are three very different jobs with three very different prices. Plenty of Timonium homes have a mix, because a kitchen or an addition was wired in a later decade than the rest of the house, so we check each part rather than assume.

Rewiring in Timonium

Not sure we cover your street? Call or text 410-808-4215.

Why it comes up here

Why Timonium homes from the 1950s to 1970s need wiring work

A Timonium rancher from the 1950s was wired for a household with a fraction of today’s plug-in load. Bedrooms often share one circuit, the kitchen may have only one or two countertop outlets, and the cable from that era frequently has no equipment ground. The insulation on it is rubber or early plastic that has spent sixty-plus years heating and cooling in the walls and attic. Where it’s stapled tight or bent sharply into a box, it can crack. Many of these houses also got central air, a finished basement and a remodeled kitchen decades after they were built, and each of those projects leaned on the original circuits a little harder.

Split-levels and later ranchers from the 1960s are more likely to have grounded cable, but the circuit layout is still thin. These are the houses where a breaker trips when the space heater and the vacuum run together, or where the family room on the lower level shares a circuit with half the bedrooms upstairs. The cable may be sound. The problem is that there isn’t enough of it. Owners respond with power strips and extension cords, which moves the problem around without fixing it. Adding a few well-placed circuits is often the most useful wiring work a 1960s Timonium house can get.

The late-1960s and 1970s homes add a third question. For a stretch of those years some builders used solid aluminum branch wiring. Aluminum expands and contracts more than copper, and connections at outlets, switches and splices can work loose and run hot. That doesn’t always mean replacing the wire. Copper pigtails attached with connectors listed for aluminum-to-copper are a recognized long-term repair, and we explain the difference between those and a full rewire.

On top of all three, Timonium houses change hands regularly, and buyers’ inspectors write up ungrounded outlets, aluminum branch circuits and old add-ons. A plan made before you list is easier on everyone than one made against a closing date. If you’re the buyer, an inspection before closing tells you what you’re taking on and gives you something concrete to negotiate with.
Solid aluminum branch wires on an old outlet with discoloration at one terminal.

SOLID ALUMINUM

Branch wiring from the late 1960s and 1970s
Electrician's hands installing a new outlet in a freshly finished room.

NEW CIRCUIT

Grounded outlet installed on new cable

What we do

How we rewire a Timonium rancher or split-level

We start by identifying the wiring. We check cable markings in the basement and at the panel, open a sample of outlets and switches on each level, test for ground, and look for heat damage. Then we map which rooms share which circuits. You get a plain list: the circuits that are sound, the ones that should be replaced, and the ones that just need more company.

Ranchers are the easiest houses in Timonium to rewire. With a basement below and an attic above, new cable can be fished to most rooms through small openings at the boxes. Split-levels take more planning because the levels overlap, so cable often travels through closets, the stair wall or the space under the upper floor. Finished lower levels with drywall ceilings slow things down, and we show you where any openings will be before we cut.

New circuits get grounded, tamper-resistant outlets with AFCI and GFCI protection where the 2023 NEC requires it. Kitchens get the dedicated small-appliance circuits they’ve been missing. On aluminum-wired homes we either pigtail every connection point or replace the aluminum with copper, depending on what the rest of the job looks like. If the panel is an older model, or too full for the new breakers, we quote a panel upgrade as part of the plan.

A rewire is also the moment to add what’s hard to add later. Recessed lighting in a living room with an 8-foot ceiling, hardwired and interconnected smoke alarms, and an outlet where the TV actually sits all cost less with the cable already being run. Those go on the quote as separate lines, so you can take them or leave them. A ranch-house basement that will be finished someday is worth a look too; running a few home runs now is cheap insurance against opening a finished ceiling later.

How the visit goes

How a Timonium rewire runs

Most Timonium families stay home through the work. The plan keeps a kitchen, a bathroom and the bedrooms usable.
Michael Cliffe standing behind the Snapper Electric truck with ladders on the roof rack

SINCE 2005

Owner-led jobs across three counties

1

Identify and map

We confirm the wire type, test every room and the panel, and map the circuits. A typical rancher or split-level takes a couple of hours.

2

Options in writing

You get choices, such as a ground retrofit, aluminum pigtailing or a partial or full rewire, each with up-front pricing, so you can phase the work.

3

Permit and room order

We pull the Baltimore County permit and order the rooms around work, school and cooking. You’ll know ahead of time which day the kitchen or a bathroom will be without power, and bedrooms are usually back on by evening.

4

Rough-in, inspect, finish

We run new cable, pass the rough-in inspection before patching, then install devices, test each circuit and update the panel directory.

Free video estimate

Need a Quick Quote?

Send a short video to 410-808-4215 showing the area where you’re experiencing an issue or where you’d like work completed. Please include as much detail as possible so we can provide the most accurate estimate.
Please Note: Quotes provided from videos are estimates based on the information shown. If additional issues, repairs, materials, or site conditions are discovered that were not visible in the video, the final cost may vary. A more detailed video helps ensure the most accurate quote.

Cost factors

What changes the price of rewiring in Timonium

The wiring era of the house is the biggest single factor. These are the rest.

Wire type found

Pigtailing aluminum, adding grounds and full replacement are three different scopes and prices.

How much of the house

One problem circuit, the kitchen and bedrooms, or every room and level.

Rancher or split-level

A rancher over an open basement is quicker to fish than overlapping split-level floors.

Finished lower levels

Drywall ceilings and paneled family rooms take more openings than open joists.

Panel condition

Older or full panels may need replacing to hold new AFCI and GFCI breakers.

Permit and add-ons

Baltimore County permit fees, inspections and any lighting or alarm work you add to the job.
A video estimate gets you a starting figure; the on-site inspection confirms it. Veteran, teacher and senior discounts are available.

Permits

Permits in Baltimore County

A rewire in Timonium is permitted through Baltimore County’s Permits, Approvals and Inspections office at 111 W. Chesapeake Ave in Towson. The county requires a permit for nearly all electrical work, pulled by a county-registered licensed electrical contractor, and inspects permits issued after August 31, 2023 to the 2023 NEC. We pull the permit when the job requires one, schedule the rough-in inspection before walls are patched, and meet the inspector for the final.

Aluminum pigtail repairs are smaller in scope, and whether they need a permit depends on the work involved. We check before we start rather than assume. Condo owners in Mays Chapel and nearby communities should also check their association’s rules on contractors and work hours. For any job that changes the service or the meter, BGE handles the disconnect and reconnect, and we book that appointment for you.

Baltimore County permit file

PERMIT OFFICE

Baltimore County Permits, Approvals & Inspections, 111 W. Chesapeake Ave, Towson · 410-887-3900

CODE IN FORCE

2023 NEC for permits issued after Aug 31, 2023

UTILITY

BGE

01

Permit

We apply for the permit before work starts, when the job requires one.

02

Work to code

We wire it to the code your county enforces, with the right parts for the job.

03

Inspection

The county inspector checks the work before walls close or the power is restored.

04

Walkthrough

We show you what we did, what passed and anything worth planning for next.

Reviews

What neighbors say

Posted on Google Google
Kyle Harbaugh profile picture
Kyle Harbaugh
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I called Snapper Electric for an after-hours service late on a Sunday evening. Unfortunately, they weren't able to make it to my house but diagnosed the problem over the phone and got me on the right track calling BGE. This is what great customer service is all about! In the past, I've used them from everything from light installs to outlet rebuilds. All the work has always been done to perfection.
Posted on Google Google
Alice Alice profile picture
Alice Alice
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Replaced our outdated electrical panel and fixed a few wiring issues the same day. Professional, punctual, and everything works perfectly now.
Posted on Google Google
monte combs profile picture
monte combs
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
And his service remains 5 star. This was the first time that I have used Mike but rest assure it will not be the last. He was quick, he was honest and his work was exemplary and his prices are more than reasonable. Keep up the good work SNAPPER!
Posted on Google Google
Linda Diaz profile picture
Linda Diaz
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Maryland.... NEED AN ELECTRICIAN?..... Look no further! Words escape me at the amazing customer service delivered by Mike Cliffe(Master Elec.) at Snapper Electric. I called to inquire about services to uninstall my Chargepoint EV home charger. Michael said he can come by to work on this for me. He asked me to send him pics so he can advise properly. I sent the pics and Michael responds back with where to look and how to uninstall. I was shocked! No call charge. No service charge. Just the instructions and he wishes me an amazing weekend!!! Honest and great customer service 👍
Posted on Google Google
Mark C profile picture
Mark C
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Mike came out, quickly diagnosed the problem and fixed it very quickly. He is great, and very reasonably priced! Would definitely use them again!
Posted on Google Google
M G profile picture
M G
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Great work done after a thoughtful discussion on all options
Posted on Google Google
Steve Somers profile picture
Steve Somers
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I bought a new electric range and didn't realize the old one was hard wired in. I called Mike and he was out right away to get a new outlet installed for the new range. I highly recommend!! Super Fast and Professional!!!
Posted on Google Google
John Brodrick profile picture
John Brodrick
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I have had them do a few jobs for me including installing a generator outlet for the house and some wiring throughout the house. He took the time to explain options and what was best to fit my needs. Overall very professional, on time and did great work. Highly recommended.
Posted on Google Google
Ricky Godbolt profile picture
Ricky Godbolt
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I highly recommend Snapper Electric.
Mike was not only on-time, but early to the appointment! Very responsive by text messages which is the best way to get hold of me. I had a problem with bathroom lights and multiple outlets that stumped me - I tried but couldn't figure it out myself.
Clayton Jones
Google review
Mike was able to come out and assist us very quickly. He was polite and explained exactly what needed to be done to fix our problem. Very professional work done in a timely manner. Definitely recommend!
Shannon Baumgart
Google review
My wife was home during installation. She was pleased with the time he took with her to discuss and plan light placement. I was told he worked cleanly and diligently. He was very respectful of our home.
Brian Ferullo
Bel Air, MD

From the blog

Read more about this

The factors behind a rewiring price, and how phasing works.
What an electrical inspection before closing covers.

FAQ

Rewiring questions from Timonium homeowners

Not always. Two-prong outlets mean no equipment ground, but the cable may still be in fair shape. We test it and look at the insulation where we can see it. Some owners replace the kitchen, bathroom and office circuits with new grounded cable and add GFCI protection labeled “No Equipment Ground” in the remaining rooms. Others go whole-house. We price both.
Look at exposed cable in the unfinished part of the basement or near the panel without touching anything. Aluminum cable is often printed “AL” or “ALUMINUM” on the jacket, and the wire is dull silver. Don’t open outlets to check. We confirm it at the devices and tell you whether pigtailing or replacing makes more sense for your house. Finding it is not a reason to panic; it’s a reason to have the connections checked.
Pigtailing usually costs less, because the existing wire stays and only the connection points are repaired, every outlet, switch, fixture and splice. A rewire costs more but suits homes where walls are being opened for a remodel or where other wiring needs replacing too. We lay out both so you can compare.
Yes. It takes more planning, because the floors overlap and the family room ceiling is often drywall. We route cable through closets, the stair wall and the attic where we can, and make small marked openings where we can’t. If you’re thinking about recessed lights down there anyway, they can sometimes share the same openings.
Partly, in most cases. Inside the unit, circuits that feed your rooms can be replaced or added, though shared walls and ceilings limit routes, and associations often have rules on contractors and work hours. We look at what’s possible in your unit and work within the association’s requirements.
Yes, as a starting figure. Text a video of the panel, a couple of outlets and switches with the covers off and any exposed basement cable to 410-808-4215. We firm up the number after seeing the house in person, because most of the wiring is out of sight.
Michael Cliffe, owner of Snapper Electric

Reviewed by Michael Cliffe, Owner · Maryland State Licensed Contractor, License 7788

Written by the Snapper Electric team · Last updated October 25, 2026

Electrical work can be dangerous. The information on this page is general guidance for homeowners in Maryland and is not a substitute for an on-site assessment by a licensed electrician. Always turn off power at the breaker before touching any wiring, and call 911 if you smell burning, see sparks, or have an active electrical fire.

Ready when you are.

Call, text, or send the form. We’ll tell you what we see, what it means for your home, and what it costs before any work starts.
Office hours Mon–Sat 8 AM–5 PM · 24/7 for electrical emergencies
Snapper Electric turtle mascot